Skip to content

Uniform design, manufacturing and supply for institutions in Egypt, with export to the Gulf, Africa and Europe

العربية
نسج مصر
Guides

Logo placement and sizes on uniforms: artwork to send

Logos go on uniforms by flat or 3D puff embroidery, woven or embroidered patches, screen printing, DTF and heat transfer, or sublimation on polyester. This guide shows schools and companies where the logo usually sits and at what size in centimetres, which artwork files to send, how to approve a sample, how to care for the logo and how repeat orders stay consistent.

Written by , Design and production team at Nasj Egypt

Published · Last updated

The short answer

Most organisations put their logo on uniforms in one of five ways: embroidery, a sewn or pressed patch, screen printing, DTF or heat transfer, and sublimation. Embroidery is the usual choice for blazers, shirts, polos, scrubs and caps because it lasts as long as the garment. Printing suits T-shirts, sportswear and large designs. The sections below cover the practical side: where the logo goes and at what size, what artwork to send, how to approve a sample, how to wash a branded uniform, and how to keep every repeat order looking the same. For a side-by-side comparison of durability and setup, read our guide on embroidery versus printing.

Embroidery: flat, 3D puff and appliqué

Embroidery stitches the logo into the fabric with polyester or rayon thread. A machine follows a digitised stitch file, prepared once from your logo and reused on every order.

Type What it looks like Best for Limits
Flat embroidery Stitches lie flat on the fabric Shirts, polos, blazers, scrubs, lab coats Very small text and thin lines lose clarity
3D puff Raised letters over a foam layer Cap fronts, bold initials, simple shapes Needs thick, simple letters; no fine detail
Appliqué A fabric shape stitched on, with an embroidered border Large logos on jackets, hoodies, team wear Best with a few large, solid areas

Thread colours. Most commercial embroidery machines carry between 12 and 15 needles, one colour per needle, but logos stitch most cleanly with up to six to eight colours. Gradients and photographic effects cannot be embroidered faithfully; they need to be simplified into solid colour areas or moved to print.

Size and detail limits. As general industry guidance, embroidered text should be at least about 0.5 cm high, and lines at least about 1 mm thick. A typical left chest logo carries several thousand stitches. A large, dense design on a light fabric can make the area stiff and pucker the cloth, so large back designs are often done as appliqué or print instead.

Which fabrics. Embroidery works best on stable woven fabrics (poplin, oxford, gabardine, twill, melton) and on firm knits such as piqué, fleece and heavy jersey. Thin, stretchy jerseys and lightweight dry-fit fabrics need a lighter stitch density and the right backing, or a print method.

Woven labels and patches

A patch is made separately and then sewn, ironed or fixed with hook-and-loop to the garment. Embroidered patches suit school blazer pockets, security shoulder badges and work jackets. Woven patches are made on a loom with fine thread, so they carry smaller text and finer detail than direct embroidery, which helps with detailed crests. Woven labels are also used inside the collar or on the hem to carry the organisation's name and care instructions. A patch is useful when the same crest moves across several garments, or when the garment is too thick or already made.

Printing methods

Screen printing pushes ink through a fine mesh screen, one screen per colour. Once the screens are ready, each extra piece prints quickly, so it suits large runs of the same design on cotton and blended T-shirts and hoodies. It is less suited to many-coloured or photographic logos.

DTF and heat transfer. DTF (direct to film) prints a full-colour design on film, which is then heat pressed onto the garment. It works on cotton, blends and polyester, including dark colours, and needs no screens, so it suits small quantities, many colours and names or numbers that change from piece to piece. Classic heat transfer vinyl is cut from coloured film and suits simple names and numbers. Both sit on the surface of the fabric, so they need gentle care.

Sublimation (polyester only). Sublimation turns dye into a gas that bonds with polyester fibres, so the design becomes part of the fabric and does not crack or peel. It allows all-over colour designs and is common for football kits and printed sports T-shirts. It works only on white or light polyester or polyester-rich fabric; on cotton the colour washes out.

Name embroidery for each employee

Hospitals, hotels, security companies and service teams often add the wearer's name, with or without a job title, under or above the logo. Names are usually embroidered on the right chest or above the left pocket, with letters around 0.8 to 1.2 cm high. To order names cleanly:

  • Send one spreadsheet with each name exactly as it should appear, the script (Arabic, English or both), the department and the garment size.
  • Agree one font, one thread colour and one letter height for the whole team.
  • Check the list for spelling before stitching, because each name is a separate piece of work.

For staff who change often, a hook-and-loop name tape or a separate name badge may be more practical than stitching the name into the garment.

Logo placement standards and typical sizes

The sizes below are common industry guidelines, not fixed rules. They change with the garment size, the logo shape and the fabric, and the final size for each garment is fixed on the sample.

Position Typical size Used on
Left chest 7 to 10 cm wide Shirts, polos, scrubs, jackets, hoodies
Blazer breast pocket 6 to 8 cm wide School and corporate blazers
Right chest (name) Letters 0.8 to 1.2 cm high Scrubs, lab coats, hotel and security wear
Sleeve or shoulder 5 to 8 cm wide Polos, security shirts, jackets
Upper back (below collar) 8 to 10 cm wide Polos, T-shirts, work jackets
Full back 25 to 30 cm wide Jackets, coveralls, hoodies, event T-shirts
Cap front 5 to 6 cm high, up to about 11 cm wide Caps

The left chest logo is usually centred about 18 to 23 cm below the shoulder seam on an adult garment, between the centre front and the side seam. On ladies' cuts and small children's sizes, a slightly smaller logo or a size set by size band keeps the proportion right. Large organisations usually write these positions into a branding sheet so every branch receives the same layout.

Artwork files to send

  • A vector file in AI, PDF, SVG or EPS format. Vector files scale without losing quality and give the cleanest embroidery and print files.
  • Colour references as Pantone codes, for example a Pantone Coated reference for each logo colour. Thread and ink are then matched to the nearest available shade.
  • The font used in the logo, or the text converted to outlines.
  • A placement note for each garment: position and width in centimetres.
  • Your brand guidelines, if you have them, including any rule on minimum logo size or clear space.

If you only have a JPG or PNG, send the highest resolution available. The logo is then redrawn as a vector before the embroidery or print file is made, and you approve the redrawn version.

Approving a pre-production sample

Approve the logo on a real garment before the full run, not only on screen. Check:

  1. Colours against your Pantone references under daylight.
  2. Size and position on more than one garment size.
  3. Small text and fine lines for clarity.
  4. The feel of the fabric around the logo, with no puckering or stiffness.
  5. Spelling of any names or slogans.

Sign off the sample and a short specification sheet listing method, position, size and colours for each garment. That signed record is what the production run, and every later order, is checked against.

Wash care to protect the logo

Method Washing Ironing
Embroidery and patches Copes with frequent and industrial washing Iron on the reverse side
Screen print Turn inside out, avoid very hot washes Do not iron directly on the print
DTF and heat transfer Turn inside out, low or no tumble drying Never iron directly on the print
Sublimation Normal washing for polyester Low heat, polyester setting

Avoid bleach on coloured logos and avoid fabric softener on printed areas, as it can weaken adhesion. If the uniform goes to an industrial laundry, say so in the request, because it changes which method is recommended.

How repeat orders stay consistent

Uniforms are reordered for new staff, new pupils and replacement pieces, and a logo that shifts in colour or size from batch to batch is noticed quickly. Keep the approved sample and the signed specification sheet at your end. Nasj Egypt keeps the approved logo file, the thread colour references and the size chart from your order on file, and uses them for every repeat order, so the new batch can be compared directly with the approved sample. If you update your logo, send the new file and approve a new sample before the next run.

Garments in this guide

Uniform accessories

Blazers and jackets

Medical scrubs

Polo shirts and T-shirts

Tracksuits and sportswear

Workwear and coveralls

Frequently asked questions

Frequently asked questions

What is the usual size of a left chest logo?
A left chest logo is usually 7 to 10 cm wide on shirts and polos, slightly smaller on ladies' cuts and small sizes. These are common industry guidelines, and the final size for each garment is fixed on the sample before production.
Can a logo with very fine detail or small text be embroidered?
Embroidery has a detail limit. Text under about half a centimetre high and very thin lines lose clarity. In that case we suggest simplifying or enlarging the logo, or using a woven patch or DTF print, which hold finer detail.
Does sublimation work on cotton shirts?
No. Sublimation works only on polyester or polyester-rich fabrics in light colours, because the dye bonds with polyester fibres. Cotton and cotton-rich blends suit screen printing, DTF or embroidery instead.
How do we order a name embroidered on each employee's uniform?
Send one spreadsheet with each name exactly as it should appear, the script, the department if any, and the size. We agree the font, thread colour, letter height and position, and the list is checked before stitching to avoid spelling errors.
Which logo files should we send?
Ideally a vector file in AI, PDF, SVG or EPS format, with Pantone references for the logo colours and the font if the logo contains text. If only an image exists, send the highest resolution available so it can be redrawn before the embroidery or print file is prepared.
How do we make sure a repeat order matches the first one?
Keep the approved sample and the signed specification sheet. We keep the approved logo file, thread colour references and size chart from your order on file, use them for every repeat order and compare the new batch with the sample.

Ready to dress your organisation?

Send the garments and approximate quantities and our team replies with a written quote and a sample proposal.